fbpx

DIY Wooden Planter

Making this modern planter is easy using PAR pine that you can buy at any Builders Warehouse – have it cut to size for easy assembly.

diy modern plant stand

Made using PAR pine, this modern planter would look stunning in any room – or apply exterior sealer to place it outdoors on a deck or patio.

diy modern planter

This modern planter by DIY Creators is very easy to make, and we have made some modifications to the design and materials used to allow for local products available in South Africa.

make a modern planter

YOU WILL NEED:

1 of 19 x 882 x 282mm pine – base

2 of 19 x 920 x 200mm pine – planter front/back – ends cut at 45-degree bevels

2 of 19 x 320 x 200mm pine – planter sides – ends cut at 45-degree bevels

4 of 44 x 44 x 660mm pine – legs

2 of 44 x 44 x 610mm pine – top rails

11 of 44 x 44 x320mm pine – planter support/shelf end/slats

2 of 19 x 44 x 566mm pine – shelf, stretchers

25mm coarse thread screws [16]

60mm screws [18]

8mm pine dowel

Hacksaw or finishing saw

Plastic planter box to fit

Waterproof lining for planter

Wood glue, exterior

Choice of finishing

TOOLS:

Drill / Driver plus assorted bits

Kreg pocket hole jig (or assemble with basic joints)

Clamps

Mitre saw or table saw

Wood chisel or Bosch multifunction tool

Orbital sander plus 120- and 180-grit sanding pads

Staple gun

Tape Measure and pencil

You can buy everything you need for this project –  and have all the pieces cut to size – at Builders Warehouse.

plan

The finished modern planter measures 800mm height x 960mm length and you can modify these measurements to fit a specific plastic planter box size.

diagram
diagram

HERE’S HOW:

instructions

1 Use a table saw or mitre saw to cut 45-degree bevels at the ends of the front, back and sides for the planter.

instructions

GOOD TO KNOW: Set up your Kreg pocket hole jig for 19mm thick material.

DIAGRAM: Secure base to Front and Back

diagram

2. Drill [6] pocket holes along the long sides of the base and [2] pocket holes at the ends of the base. If you are not using a pocket hole jig, drill countersunk pilot holes through the front, back and sides.

kreg pocket hole jig

3. Attach the [C] Base to the [A] Front and Back with exterior wood glue and 25mm screws.

join with pocket holes

DIAGRAM: Secure base to Sides

diagram

4. Attach the [C] Base to the [B] Planter Sides with exterior wood glue and 25mm screws.

pocket hole joints

DIAGRAM: Secure Rails to Legs

diagram

5. Secure [E] Top Rail to [F] Legs. Clamp the Top Rail firmly on top of the Legs in order to drill an 8mm hole through the Rail into each Leg to a depth of 20mm. .

instructions

6. Apply wood glue and hammer in an 8mm pine dowel.

instructions

7. Use a saw to trim off the excess dowel.

instructions

8. Clamp the legs and put aside for a couple of hours.

instructions

DIAGRAM: Attach Planter Supports

diagram

9. Measure and mark at 122mm down from the top of each Leg to fit the [D] Planter Upper Support. Apply glue and clamp in place.

instructions

10. Repeat steps 5 to 7 above to drill an 8mm hole, push in a dowel, and trim off excess.

instructions

DIAGRAM: Cut [G] Shelf Ends and [H] Shelf Slats

diagram

11. On the Shelf Ends and Shelf Slats, measure and mark at 50mm in from both ends. Draw a line across to mark where the cut a lap joint.

instructions

12. On the shelf end also mark the centre (22mm) and cutting depth (19mm) for the 19 x 44mm Stretcher.

instructions

13. Cut away the lap joint on the slats using a mitre saw (set to cutting depth) or table saw (height adjustment locked in).

instructions

BELOW: Finished Shelf Slats

instructions

14. To cut out the rebate in the Shelf Ends, you can use a hammer and wood chisel…

instructions

Or you can use a Multifunction tool to make this job much easier and faster.

instructions

GOOD TO KNOW: Test fit that the rebates fits the Stretcher snugly.

instructions

15. Sand down all the assembled parts to a nice smooth finish.

sand all the pieces

DIAGRAM: Install Shelf Ends

diagram

16. Cut a 100mm long spacer and use this to mount the [H] Shelf Ends between the Legs.

instructions

GOOD TO KNOW: Glue and clamp the Shelf Ends in position.

instructions

17. Repeat steps 5 to 7 above to drill an 8mm hole, push in a dowel, and trim off excess.

instructions

18. Apply your choice of finish to the Planter box and Shelf Slats. 

instructions

19. Stain or paint the Leg frames in your choice of colour. For this project a light colour was selected for the planter box and slats and a dark colour for the leg frames and stretcher. DO NOT paint the Shelf Ends.

paint the frame

GOOD TO KNOW: Allow the paint to dry and then mask off in order to stain the Shelf Ends.

instructions

DIAGRAM: Install Stretchers

diagram

DIAGRAM: Install Shelf Slats

diagram

20. Turn the frame upside down to install the stretchers and Shelf Slats with wood glue and 60mm screws.

instructions

Finishing

instructions

Cut a piece of liner to fit inside the planter box  and staple in place.

instructions

Pot up your choice of plants.

instructions

Place the plaster planter box inside the frame.

instructions

Place a few small pebbles or stones on top of the soil for a nice contrast.

instructions

Your modern planter is now ready for use. Be sure to select the right type of plants for the setting where the planter will be placed.

diy modern planter

DIY guide brought to you by Home-Dzine.

designmind

DesignMind is an on-line market place for South Africans to find inspiring home building and decorating ideas and the suppliers best able to make home improvement dreams a reality.

Related Posts

Latest Stories

Search stories by typing keyword and hit enter to begin searching.