fbpx

Make a Server for your Dining Room

Using a simple basic box frame design, this server or sideboard is perfect for a dining room, or you can even use it in a bedroom or living room.

This plywood server or sideboard is a great addition to a dining room. You can create a focal point with a few decor accessories and pack the shelves with flatware and cutlery, or items you want close to the dining table. The unit can also be used as a media cabinet for your TV or hi-fi, or in a bedroom to provide more storage.

You can follow the step-by-step instructions below, or take a look at the video at the bottom of this page.

YOU WILL NEED:

Sheet of 18mm pine plywood cut to the following sizes:

4 of 500 x 400mm – box sides

2 of 364 x 400mm – bottom / shelf, small box

2 of 764 x 400mm – bottom / shelf, large box

4 of 364 x 70mm – struts, small box

4 of 764 x 70mm – struts, large box

1 of 500 x 1200mm – back

2 of 500 x 440mm – sides, outer frame

2 of 1240 x 440mm – top and bottom, outer frame

3 of 492 x 392mm – doors

Chipboard screws 6mm x 50mm, 8mm x 30mm and 6mm x 16mm

6 Concealed hinges

4 Legs, style of your choice

Sealer or varnish – clear or tinted – plus paintbrush

Pack of shelf pins

TOOLS:

Drill / Driver plus assorted bits

Countersink bit

24mm spade bit

Orbital Sander plus 120- and 240-grit sandpaper

Quick clamps

Tape measure and pencil

Not responsible for errors or omissions

Buy everything you need for this project at Builders Warehouse.

diagram for server sideboard

HERE’S HOW:

make a diy dining server assemble small box

1. Assemble the smaller boxes by joining the 364 x 400mm bottom between the short sides of [2] 500 x 400mm box sides. These are screwed together using 50mm screws. Screw [2] 364 x 70mm struts between the other short sides (the top) and the other two at the back.

GOOD TO KNOW: Drill 3mm pilot holes and countersink all visible screws (that will show on the outside of the frame).

make a diy dining server assemble large box

2. Repeat the same process for the larger box, but substitute with the 764mm pieces. Join the two boxes together with 30mm screws.

GOOD TO KNOW: Use quick clamps to hold the boxes firmly in position while joining.

make a diy dining server

3. Place the server on its back – facing upwards. Join the 500 x 1200mm back piece. This piece will keep the server square and sturdy.

4. Measure and mark the location where you want to position the legs. These will be positioned at the corners (of the 1240 x 440mm bottom) of the outer frame. Drill pilot holes before attaching the legs with 50mm screws.

make a diy dining server add legs

5. Place the server upside down in order to screw the base in position. Make sure the rear edge sits flush with the back.

make a diy dining server add base

6. Attach the [2] 500 x 440mm sides of the outer frame to the box sides – from the inside. Place the sideboard upside down on top of the remaining 1 240 x 440mm piece and screw together from inside. This will form the top of the sideboard

make a diy dining server add top

7. Now you’re ready to attach the doors. We used concealed hinges for the doors and you will find more information in this article for drilling the holes in the door. Screw the hinges to the door with 16mm screws and then use a 3mm spacer to hold the doors in place before you screw them to the sideboard.

8. Measure and mark 60mm from the top and side of each door and drill a hole with the 24mm spade bit – this serves as a handle. Alternatively, you can add your own decorative handles or knobs.

9. Decide how high you want the shelves in each section and drill 6mm holes for the shelf pins.

make a diy dining server add doors

Finishing

 Once the assembly is done, sand the server with 120-grit to remove any rough edges and then with 240-grit to smooth. Seal or varnish in your choice of finish.

If you prefer to keep the finish as natural as possible, use Rust-Oleum Ultimate Polyurethane – Natural Matte.

rust-oleum polyurethane sealer with matt finish

DIY steps brought to you by Home-Dzine

designmind

DesignMind is an on-line market place for South Africans to find inspiring home building and decorating ideas and the suppliers best able to make home improvement dreams a reality.

Related Posts

Latest Stories

Search stories by typing keyword and hit enter to begin searching.